Buy Low Price From Here Now
The is a heavy duty, 2 in 1 pneumatic flooring nailer. It is designed to install tongue and groove hardwood flooring with L-shaped nail or staple. Flooring in thicknesses of 1/2", 5/8", 3/4" and 25/32" can be installed using 1.5" and 2" length nail respectively.
Your purchase includes: Brand New Factory Sealed box containing the 2-in-1 Flooring Cleat Nailer and Stapler. Heavy Duty Blow Mold Carrying Case. 2 oz bottle of Oil. High Quality light weight white rubber non marring Mallet. Detailed Instruction Manual. Detailed Internal Component Diagram. All necessary tools to service the product. Four Hex Keys. Service Wrench for adjustment, assembly, and repair. Non-Marring base flooring plate for installing 1/2" or 5/8" flooring. Non-Marring base flooring plate for installing 3/4" or 25/32" flooring. Safety Protective Eye Goggles. Complete Rebuild/Repair kit, includes Gaskets, O-Rings, Seals, and Springs to rebuild the entire gun.
Readmore
Technical Details
- Can be used on 1/2", 5/8", 3/4" and 25/32" floor thickness- Uses 15.5 Gauge Staples from 1" to 2"
- Uses 16 Gauge L-shaped Nail from 1.5" to 2"
- Operating Air Pressure: 60-100 PSI
- Light die cast aluminum body
See more technical details
By Sawzall (Mohnton PA)
I purchased this nailer to install 1500 square foot of 3/4 solid walnut for a customer. Rental fees would have exceeded the cost to purchase this nailer and based on the reviews, it seemed like a decent choice (and it was about the only type of nailer I didn't own yet...). Nailer arrived within a couple days. Case is nice and contains most everything needed to maintain the tool. Tool even comes with an industrial standard air fiting installed.
It drove nearly every cleat perfectly and I only had one jamb that was caused by my lightly bumping the striker (which will partially drive a fastener) and then striking it for real - jamb was easily cleared by removing one plate with the tools provided. I used only Bostitch cleats.
I noticed that it didn't sit perfectly flat on the flooring with the base plate provided so I added a shim made from high pressure laminate (Formica) between the base plate and the nailer. The addition of that shim made the nailer sit perfectly on the wood. I didn't use it without but it shouldn't make too much of a difference.
The mallet provided with my nailer was very good and I had no problems with it at all as some of the others reported.; maybe they got the word. I did use it hard and for the entire 1500 sq. ft.
Now, the one flaw. I read some other reviews where they stated that the nailer started leaking air. This one did too but only intermittently. It would sometimes bleed a little air when the safety trigger remained compressed between shots. The leaking air did not affect the ability to drive fasteners at all and came and went about three times per room - not a big deal but a bit annoying. I did not rebuild the nailer with the o-rings provided. Figured I wait until it really didn't work.
I would recommend this nailer for the serious DIYer or the occasional flooring install for a remodeling contractor like myself.
By Brett Bowers (Battle Creek, MI USA)
After renting a nail gun locally over the past year and installing Oak, Hickory and Bamboo in our house, I decided that it made sense to buy rather then rent. So we do not have to rush the job and get the nailer back to the rental shop. One Sunday we stayed up until 3am so we could finish the flooring installation and get the nail gun back in time Monday morning.
I ordered the Akuzuki floor stapler and nail gun. It is easy to use and you can load both staples or nails/cleats and use on different sizes of flooring I.E. 5/8 or 3/4. I have used it to install Maple and the only problem I had with it was that it left small indentations on the wood from the base plate. I found that I might have been putting too much weight on the base plate with my foot to hold it in place and keep it from rebounding. I also put some duct tape on the hard plastic base plate to soften it a bit. That seemed to work.
In the end I am very pleased with this nail gun and now I can start a project when I want and can avoid the time, gas and hassle of going to a rental shop. I still have some bamboo, mahogany and more maple to install so I am hoping.
By M. Poulos
This tool is a piece of junk. It did not work right out of the box. Never by a tool made in China. I had to spend $80.00 to rent a nail gun. Do not but this tool.
By C. Ross (Wakefield, Rhode Island USA)
I installed 3 bedrooms of hardwood flooring in about 4 - 5 days with no issues. The nailer worked flawlessly and the results look great! I suggest this tool to anyone looking for a do it yourself flooring nailer. Don't spend more for a Bostich when this nailer works great.
By J. D. Keough (North Wales, PA USA)
I received the Akuzuki nailer quickly and was in good shape. As others noted, the manual is kind of lacking in quality & details. The tool appears to be of Harbour Freight quality (which is what I expected). I have a bad back and only have 500 sq ft of 3/4" oak flooring to lay so I wanted an alternative to renting (working constant till finished). I started and so far it's working fine. Hopefully I get the rest of the floor laid w/o any problems.
Images Product
Buy Akuzuki Hardwood Floor Flooring Stapler & Cleat Nailer Nail Gun Now
No comments:
Post a Comment