Factory-Reconditioned Bostitch U/BT200K-2 5/8-to-2-Inch 18-Gauge Brad Nailer

Buy Cheap Factory-Reconditioned Bostitch U/BT200K-2 5/8-to-2-Inch 18-Gauge Brad Nailer

Buy Low Price From Here Now
This is a reconditioned power tool. Reconditioned generally means that the tool has been returned to the manufacturer, who brings the tool back to like new condition. Some tools may contain cosmetic blemishes. The Bostitch BT200K-2 is a Factory Reconditioned 18 Gauge 5/8 to 2 Oil-Free Brad Nailer Kit. This lightweight tool has magnesium housing for jobsite durability. The oil-free operation prevents stains on work piece. It has ultra-quiet rear exhaust and open nose design for easy jam clearing. Includes: Brad nailer and carrying case
Readmore

Technical Details

- Drives 5/8- to 2-Inch 18-gauge brad nails
- Tool free adjustable depth control
- Lightweight magnesium housing
- Oil-free operation
- 2.5-Pound; 1-Year warranty
See more technical details

 "Great price, like new, fast shipping - No suprises!" 2010-05-23
By Gregory M. Williams (Illinois)
I've wanted a 2-inch brad nailer ever since I first used my Porter-Cable 1 3/8-inch brad nailer on some trim - it just didn't have the reach to go through the trim, drywall, and then into a stud.



Then I found the Bostitch factory-reconditioned nailer for a GREAT price! It's exactly what I wanted. It even came with a new set of 2" brad nails!



No need to buy new!

 "Go with the Senco" 2010-05-19
By Robert P. Dba Services (cape cod)
OK for the price, should of payed the extra $$ and gone with the Senco. This Bostitch miss fires to often, won't last the time the old Senco performed for me.

 "Factory Reconditioned Brad Nailer" 2010-05-14
By Rob (New Jersey)
Whenever ordering a Bostitch Factory-Reconditioned product, you always take the Bostitch gamble as to what you are going to get. This time, I was lucky and received a working product in very good condition. My last "gamble" was on a finishing nailer that did not include its accessories, the paint was quite marred, and the screws were rusty.



Mine came with an opened (but appears relatively full) pack of 2" brads. After cleaning the nailer, I hooked it up to my compressor and fired 20 nails in fairly rapid succession. 1 in 20 caused a double shot. This particular model is much more annoying to unjam as you have to unscrew three hex screws to remove the front casing, whereas on my older finishing nailer, it has 2 easy to operate clips.



Each shot (with the exception of the double shot) was consistent in depth and the easy depth adjuster worked as well as I expected.



Overall, for the greatly reduced price, if you are willing to take the Bostitch gamble, it could pay off. Worst case, Amazon is generally very good an making things right. On my aforementioned finishing nailer, they gave me a 20% refund to cover the cost of the missing parts. I honestly would not pay the full price for this product new, but with the reconditioned pricing (and the gift certificate I used), its a great nailer for the price.

 "Factory-Reconditioned Bostitch U/BT200K-2 By Big "T"" 2010-04-23
By Terence A. Molloy (Indianapolis)
I ordered through Amazon and it was shipped promptly by Bostitch. It's looks to be in like new condition and functions properly without any problems. I have used it on several small home projects and am completely satisfied with it's operation. I don't make my living with such tools so I can not comment on how it would hold up to constant use, but for a project guy like me it seems to be just fine and a good value. I recommend it and would buy it again myself if I had to do it over.

 "Worth It's Weight in Gold" 2010-04-21
By Steven R. Akers (SC)
Just completed a future room that was framed in. I used this little work horse a lot and it never missed a beat. I have a Ridgid 16 ga. nailer and this little dude went toe to toe with it. I had to face nail 3/4" maple flooring into 3/4" OSB and went to the Bostitch on the final row because it allows you to nail closer to the wall than my other gun. It had no problems sinking the 2" brads I used. I installed window and door trim with it as well. No jams, misfires, etc.

I did use Bostitch brads and would recommend that you only use them. Both guns performed perfectly and I say this little nailer is worth 10 times what I paid for it. Very small holes to putty, no hammer tracks, I just can't say enough. One of the best purchases I have made.


Images Product

Buy Factory-Reconditioned Bostitch U/BT200K-2 5/8-to-2-Inch 18-Gauge Brad Nailer Now

read more “Factory-Reconditioned Bostitch U/BT200K-2 5/8-to-2-Inch 18-Gauge Brad Nailer”

Porter-Cable US58 1/4-Inch to 5/8-Inch 22-Gauge C-Crown Upholstery Stapler

Buy Cheap Porter-Cable US58 1/4-Inch to 5/8-Inch 22-Gauge C-Crown Upholstery Stapler

Buy Low Price From Here Now
The Porter-Cable US58 1/4-Inch to 5/8-Inch, 22-Gauge C-Crown Upholstery Stapler is an easy to use pneumatic stapler with plenty of useful features. It uses standard Senco C Type 22-gauge, 3/8-inch crown staples to get the job done right, and it includes a 1-inch nose extension for those tough to reach areas. The high-capacity bottom-load magazine handles 185 staples, and the driver guide moves back to easily clear jams from the magazine. The US58 stapler requires 70-120 PSI air pressure, so it will work with most air compressors.
Readmore

Technical Details

- High-capacity pneumatic upholstery stapler with 185 staple magazine
- Uses Senco C Type, 22-gauge, 3/8-inch staples from 1/4 to 5/8 inches long
- Quick and easy jam-clearing mechanism
- Measures six inches tall and nine inches long; weighs 2 pounds
- Includes a 1/4-inch air fitting with dust cover and oil
See more technical details

 "This is a Pro Stapler for sure!" 2010-01-22
By W. Gravning
Like any well made product the Porter Cable Upholstery Stapler is absolutely a delight to use. The 1" long extension is a must for anyone working on upholstery projects. We used it recently on some oak chairs using 3/8" fine wire staples from Amazon at 70psi. Follow the instructions and you should have no problems.

 "Performed Flawlessly" 2010-01-17
By Rodney McQueen (Illinois, USA)
Have done various reupholstering projects through the years and had always hand stapled. What a difference this this tool made! It reduced the time required to complete the project and greatly improved the quality of the work. It did not "misfire" once. It is lightweight and easy to use. I highly recommend the tool, at least for home use.

 "excellent stapler" 2009-11-16
By yayamama (Western PA)
I bought this to replace one exactly like it that I have been using for 7 years. It broke because I FORGOT to oil it and the inside rusted....In conclusion take care of your tools and this is an excellent one.

 "WOW, great tool and Recommded" 2009-11-05
By Electric Z (Oregon)
Upon receiving this stapler I was using it within 10 minutes of the UPS delivery. It came with the air fitting already installed. I slapped some 1/2" staples in it and I was off working. It has a great ergonomic handle that feels great in your hand and is lightweight. My wife likes it too!



The stapler is of the high Porter-Cable expected quality. It made short work of my first project and expect many more hours of use. This tool is made for working. As fast you can pull the trigger the staples are set deep and no jamming. Recommended and the price was very reasonable.



Here it is a month later and wanted to add a couple thoughts since first purchase. First, it is working great and I am very happy.



Next, some have commented about a possible safety feature missing in that staples can be freely shot out, (no device needs to be pushed against the object being stapled first). After using it a lot, quite frankly I would find it a nuisance if there was such device. When working with fabric or some other material it would be a major impediment to have to reposition the stapler, push down and then pull the trigger. When stapling many staples with its current design you can just slide the stapler to the next position pull the trigger and move on. Much more efficient and faster.

 "Porter-cable us58 1/4-inch to 5/8 - inch 22 gauge c- crown uphoilster gun" 2009-10-02
By Plava Plumb
I purchased the gun with some reservation as to weather it would perform correctly. I am very impress with the capabilities of the upholstery gun. My product is far superior and very professional when using the upholstery gun

Plava Plumb


Images Product

Buy Porter-Cable US58 1/4-Inch to 5/8-Inch 22-Gauge C-Crown Upholstery Stapler Now

read more “Porter-Cable US58 1/4-Inch to 5/8-Inch 22-Gauge C-Crown Upholstery Stapler”

Surebonder 9600 Pneumatic Fine Wire Staple Gun with Carrying Case

Buy Cheap Surebonder 9600 Pneumatic Fine Wire Staple Gun with Carrying Case

Buy Low Price From Here Now
Lightweight, air-operated staple gun is easy to use on a number of projects. Accepts a variety of staple sizes for different applications. Operating PSI: 60 - 100, Fasteners Used: No.4 Staples, Fastener Sizes (in.): 1/4, 5/16, 3/8, 1/2 and 9/16, Fastener Capacity Per Strip: 100, Coil or Strip: Strip, Inlet Size (in.): 1/4, Min. Hose Size (in.): 3/8, Case Included: Yes, Tool Length (in.): 2.9, Tool Weight (lbs.): 8 29/32
Readmore

Technical Details

- Drives 1/4" thru 9/16" staples
- Safety mechanism prevents accidental firing
- Quick release magazine for easy loading
- Adjustable air exhaust & Staple viewer
- Staples to be used with this gun include B000BQUGRA and B0000BYC2R
See more technical details

 "Small Wonder" 2010-05-28
By Metal Polisher (Waterford, MI USA)
I mostly use heavier gauge staples, however, when I need T-50 staples, I found this to be far superior to a manual Arrow stapler that I had used in the past.

Having lots of T-50's in every size for hammer tackers, I bought this to use T-50's in an air-powered tool when I need many, rapid fastenings. This is a great stapler and at a great price: case is included,and it has a safety so it permits bump fire operation, unlike my dedicated Porter-Cable US-58 which has no safety, and fires with each trigger pull, with no bump fire.

It's small and nearly lays in one hand, but easy to load and use.

 "staple gun" 2010-05-10
By Country Additions Inc. (Birdsboro ,PA USA)
I wanted a small light staple gun to dc a little upholstery work for some of the products we produce in our wood shop. So far this stapler has done the job that I had intended to use it for. Has already paid for itself in labor cost. If I were to do all upholstery work, i would probably go for a more expensive gun, but at this point why waste money. More expensive isn't always better.



Vince

 "works great" 2010-05-06
By Glon I. Rose
I did a upholstery project with this and it worked great. I think it's great that it takes standard t50 staples. I insulated a couple of rooms the other day and wish I brought it with me. only downside is it doesn't hold a lot of staples.

 "surebonder 9600" 2010-05-04
By D. Vanderwell
I purchased this stapler because another review that I read said that it would staple a plastic pan on a motorcucle seat. Im here to tell you that it worked great. Excellent job for the money!!!!

 "Pretty clear that it is an air gun!" 2010-05-03
By Bill Hargrave (CA, USA)
For those folks out there that are giving this gun a poor review due to not knowing it needed a air compressor, first of all, if you do not know what pneumatic means, then I suggest you look it up in a dictionary. Second, the description clearly indicates: "Lightweight, air-operated staple gun is easy to use on a number of projects" Towards the bottom of the specs, it also indicates: "regulated compressed air, between 60 psi and 100 psi", and lastly, if you have every used a pneumatic tool, you could see that it needs a air compressor hose to connect the unit to it's source of power.



My entire shop is set-up on pneumatic tools, which are far superior than electric and this was a nice addition to my tool box!



Bottom line, if people would read the full descriptions of the products they are considering, the overall review score would be even higher for this product.


Images Product

Buy Surebonder 9600 Pneumatic Fine Wire Staple Gun with Carrying Case Now

read more “Surebonder 9600 Pneumatic Fine Wire Staple Gun with Carrying Case”

Stanley Bostitch Contemporary Full Strip Stapler (B2200BK)

Buy Cheap Stanley Bostitch Contemporary Full Strip Stapler (B2200BK)

Buy Low Price From Here Now
Get comfortable - sleek, ergonomic design offers comfortable hand-held use. Staples up to 20 sheets. Versatile desktop style staples, pins and opens fully for tacking. Plastic and metal construction. 3" throat depth. Top loads a full strip (210) of 1/4" standard staples. Black. Manufacturer’s one-year warranty. All sheet capacities are based on 20-lb. bond.
Readmore

Technical Details

- Contemporary full-strip, 20-sheet stapler with ergonomic design staples, pins and tacks.
- Get comfortable - sleek, ergonomic design offers comfortable hand-held use.
- Staples up to 20 sheets.
- Versatile desktop style staples, pins and opens fully for tacking.
- Plastic and metal construction; black finish.
See more technical details

 "Does the job!" 2010-05-18
By Janek51 (Portland, OR United States)
Needed a stapler that could staple 10+ pages together, the first time. Works great and took standard staples!

 "It works!" 2010-03-12
By C. J. Vazquez
This is not a luxury office item. This stapler is about as basic as you can get but it delivers what it promises. The overall feel of the stappler could be a bit sturdier but I haven't had any problems with pieces coming loose or anything like that. It made it to my four star rating because of the unbeatable price but fell short of the five stars because it doesn't offer anything special.

 "Stanley Bostitch stapler" 2009-09-08
By Leilani
I bought this stapler for work. It works very well. Great value and fast shipping. Thank you!

 "Great Stapler" 2006-10-06
By Troy
This stapler is great. It works very well and staples many papers together. If you take the top of, it becomes stainless steel. Ya its a pretty awsome stapler.


Images Product

Buy Stanley Bostitch Contemporary Full Strip Stapler (B2200BK) Now

read more “Stanley Bostitch Contemporary Full Strip Stapler (B2200BK)”

The 2006-2011 World Outlook for Manufacturing Power-Driven Hand Tools, Drills, Screwguns, Circular Saws, Chain Saws, Staplers, and Nailers

Buy Cheap The 2006-2011 World Outlook for Manufacturing Power-Driven Hand Tools, Drills, Screwguns, Circular Saws, Chain Saws, Staplers, and Nailers

Buy Low Price From Here Now
WHAT IS LATENT DEMAND AND THE P.I.E.?

The concept of latent demand is rather subtle. The term latent typically refers to something that is dormant, not observable, or not yet realized. Demand is the notion of an economic quantity that a target population or market requires under different assumptions of price, quality, and distribution, among other factors. Latent demand, therefore, is commonly defined by economists as the industry earnings of a market when that market becomes accessible and attractive to serve by competing firms. It is a measure, therefore, of potential industry earnings (P.I.E.) or total revenues (not profit) if a market is served in an efficient manner. It is typically expressed as the total revenues potentially extracted by firms. The “market” is defined at a given level in the value chain. There can be latent demand at the retail level, at the wholesale level, the manufacturing level, and the raw materials level (the P.I.E. of higher levels of the value chain being always smaller than the P.I.E. of levels at lower levels of the same value chain, assuming all levels maintain minimum profitability).

The latent demand for manufacturing power-driven hand tools, drills, screwguns, circular saws, chain saws, staplers, and nailers is not actual or historic sales. Nor is latent demand future sales. In fact, latent demand can be lower either lower or higher than actual sales if a market is inefficient (i.e., not representative of relatively competitive levels). Inefficiencies arise from a number of factors, including the lack of international openness, cultural barriers to consumption, regulations, and cartel-like behavior on the part of firms. In general, however, latent demand is typically larger than actual sales in a country market.

For reasons discussed later, this report does not consider the notion of “unit quantities”, only total latent revenues (i.e., a calculation of price times quantity is neve
Readmore

Technical Details

See more technical details

Images Product

Buy The 2006-2011 World Outlook for Manufacturing Power-Driven Hand Tools, Drills, Screwguns, Circular Saws, Chain Saws, Staplers, and Nailers Now

read more “The 2006-2011 World Outlook for Manufacturing Power-Driven Hand Tools, Drills, Screwguns, Circular Saws, Chain Saws, Staplers, and Nailers”

Campbell Hausfeld CHN10499 2-in-1 Brad Nailer/Stapler

Buy Cheap Campbell Hausfeld CHN10499 2-in-1 Brad Nailer/Stapler

Buy Low Price From Here Now
Campbell Hausfeld 2 - in - 1 18 - ga. Nailer / Stapler. Superior versatility, GREAT LOW PRICE! There's a LOT you can accomplish with one of these in your hand. Stuff you just couldn't do without it. You can't finish trim with a stapler, and you can't attach wiring with a nailer. But you can get the tool that does both. From fastening insulation, to carpeting, to upholstery, to finishing door and window trim, you won't miss a beat... just change out your fasteners in the 2-in-1 magazine and get to it! The goods: Accepts 18-ga. brad nails 1/2"-1 1/4" long, and 18-ga. 1/4"-crown staples 1/2"-1 1/4"long; No-mar tip won't dent the wood; Adjustable depth control lets you control the depth of drive in various types of wood; Adjustable exhaust lets you easily change the direction of air exhaust away from the project; Quick-clear nose lets you remove nail jams quickly, reducing downtime; Rubber comfort grip for long periods of use.; Includes: 2-in-1 Nailer / Stapler ; 1,000-count 1" staples; 1,000-count 1" brad nails; 1/4" industrial plug- 1/4" NPT; 2 allen wrenches; Bottle of nailer oil; High-impact carry case.; Order yours today! Campbell Hausfeld 2-in-1 18-ga. Nailer / Stapler
Readmore

Technical Details

- Combination brad nailer and stapler ideal for specialty work
- Features rubber comfort grip, adjustable depth control and quick clear nose
- Ideal for trim work, crafts, paneling, cabinet assembly and more
- Side-loading magazine with capacity of 100 fasteners (18 gauge brad nails or 1/4-inch staples)
- Includes 1,000 1-inch brad nails, 1,000 1-inch staples, 1/4-inch industrial plug, 2 Allen wrenches, bottle of nailer oil, and high-impact carry case
See more technical details

 "The right tool for the job" 2009-01-28
By E. Schlichtenmyer
Good shopping experience.

Good information on the tool.

The tool came ready to work and work it did. It was precisely what we needed to finish the trimwork in our dining and living rooms.

 "GREAT QUALITY, EXCELLENT PRICE" 2008-05-22
By Leda Maria (Forida,Miami USA)
NO COMPLAINTS AT ALL ABOUT THIS PRODUCT, IT HAS A NICE SHAPE AND A NEAT BODY FINISHED, EXCELLENT QUIALITY OF MATERIAL AND i THINK i FELL IN LOVE WITH THAT INTENSE BLUE COLOR, BESIDES OF THAT IT WORKS GREAT!

 "Lot of double taps..." 2004-12-18
By KRASSEL (SPANAWAY, WA USA)
I have had this gun awhile. I bought it cause it was inexpensive and I don't use nails or staples a lot, but when I need em I do need em. As the wise man said "only a rich guy can afford cheap tools".

First of all the soft nose does prevent you causing a divot in your workpiece, but the plunger makes up for it. It really makes a "slot" in your wood. Hard to hide, unless you have a putty that match's the wood perfectly. It drives the nail or staple quite deep and even with the air adjusted lower it will sometimes drive the nail or staple too deep, leaving it protruding out the backside of the two pieces. Very irratating.

This tool is prone to "double taps"....firing twice..one on top of the other...keep a pair of needle nose pliers handy...more scar's on the wood.It also will pick up two nails at the same time and try and drive em into the same hole (keep those needle nose handy). It jams a lot. The "adjustment" for nail length is a pain.

It is comfortable to hold and lightweight, other than that I can't recommend it.


Images Product

Buy Campbell Hausfeld CHN10499 2-in-1 Brad Nailer/Stapler Now

read more “Campbell Hausfeld CHN10499 2-in-1 Brad Nailer/Stapler”

Ramsond RMM4 2-in-1 Air Hardwood Flooring Cleat Nailer and Stapler Gun, Yellow

Buy Cheap Ramsond RMM4 2-in-1 Air Hardwood Flooring Cleat Nailer and Stapler Gun, Yellow

Buy Low Price From Here Now
Ramsond has quickly become a recognized name for the quality and durability of its products. The Ramsond RMM4 2-IN-1 flooring stapler & cleat nailer combination is another testament to the recognition that Ramsond tools now enjoy. With over 30,000 units sold in North America, the RAMSOND (R) RMM4, patented combination 2-in-1 hardwood cleat nailer and stapler is an engineering marvel. It shoots both cleat nails and staples. It shoots 15.5 and 16 gauge staples ranging from 1 to 2 inches, and "L" cleat ranging from 1-1/2" to 2". The 2-in-1 magazine has a capacity of 100 staples/cleats. It is highly durable and contractor/industrial quality, yet light weight and agile. The body of this gun is constructed of durable die-cast alloy for job site durability and low weight. It comes with an extra-wide composite non-marring base plate for added stability and protection against scratches to the flooring surface. It provides a conveniently long reach handle with an ultra-padded cushioned grip for balance and optimal operating comfort, stability and safety. Internally, the driver blade is constructed of a very tough heat treated and hardened steel. The composite base plate designed to allow the user to drive fasteners much faster and closer to the wall while protecting the flooring surface from marring. This ergonomically designed multifunctional tool is manufactured under the strict ISO guidelines for quality control. With nearly 30,000 sold, this product has become a symbol for reliability and durability.
Readmore

Technical Details

- Uses both cleats and staples
- Air operated
- Includes all accessories and carrying case
- Uses l cleats and u staples
- Air booster chambers for better nail driving
See more technical details

 "Excellent Floor Nailer" 2010-05-19
By Betsy J. (Huntington Beach, CA)
This is an excellent tool. We received it very quickly and haven't had any problems with it in the year we have had it.

 "Well worth the money" 2010-04-27
By Mike T (sterling, Ma.)
So far i have used this gun twice. I have nailed down 400 sq ft so far no problems. When i got the gun i made sure every piece was tight and there were a few loose bolts. But the gun is very rugged. Im using 2 inch staples to nail down 3/4 oak. I recommend 95 psi from your compressor it sets the staple perfect. Overall i bought this gun because of the price and the reviews. I love the gun.

 "ramsond rmm4 flooring air nailer" 2010-04-27
By L. hoffman
Never worked with hardwood before so the Ramsond air nailer was almost too simple to operate. Put down 500 sq. feed of 3/4" rustic red oak without a single misfire or jam ( 3000 2" nails ). Guess I'll have to find another project to see how long it takes before it jams of misfires. Great product, great price. Would have helped to know the principle of how the air nailer tightly fastens the wood down and forces the wood tightly to the adjacent board.Highly recommend this product. Len in Colorado.

 "Move Over Bostitch. There is a new king in town" 2010-04-26
By Frenchy Joe (Quebec Canada)
Having used Bostitch before, this tool blows it out of the water on all fronts. 5 stars all the way for Ramsond RMM4. It's the new king in town.

 "Couldn't be more pleased. A+ Nailer" 2010-04-26
By GKNOX (Knoxville)
Great deal for the price. As a professional installer I ordered a few of these and we have been using them for the last 6 months. This tool cannot die. Amazing. How can they sell at these low prices is beyond me.


Images Product

Buy Ramsond RMM4 2-in-1 Air Hardwood Flooring Cleat Nailer and Stapler Gun, Yellow Now

read more “Ramsond RMM4 2-in-1 Air Hardwood Flooring Cleat Nailer and Stapler Gun, Yellow”

Bostitch CPACK300 3-Tool and Compressor Combo Kit

Buy Cheap Bostitch CPACK300 3-Tool and Compressor Combo Kit

Buy Low Price From Here Now
The Bostitch CPACK300R Factory Reconditioned 3-Tool Compressor Combo Pack includes an 18 gauge brad nailer and finish stapler, a 16 gauge straight finish nailer and 6 gallon compressor, providing you with all the basics needed for small construction projects, finish and repair work. Features: The CAP2000P-OFR 38-Pound 6 Gallon, Oil-Free Compressor produces 2.8 CFM @ 90PSI with 150 max. operating pressure for improved tool performance The SB-1850BN 18-Gauge 2-Inch Brad Nailer with adjustable depth guide sets nails to desired depths quickly and conveniently The SB-150SX 18-Gauge 1-1/2-Inch Finish Stapler has a bottom-loading magazine for fast loading and easy jam clearing The SB-1664FN 16-Gauge 2-1/2-Inch Straight Finish Nailer with quick release nose for fast jam clearing and adjustable depth guide sets nails to desired depths quickly and conveniently Tool-free adjustable exhausts on all three air tools direct air away from the user while no-mar tips protect the work surface What's In The Box: CAP2000P-OFR 6-Gallon 2.0 (Peak) HP Oil-Free Compressor SB-1850BNR 18-gauge 2-Inch Brad Nailer SB-150SXR 18-gauge 1-1/2-Inch Finish Stapler SB-1664FNR 16-gauge 2-1/2-Inch Straight Finish Nailer Canvas Carrying Case
Readmore

Technical Details

- CAP2000P-OF oil free air compressor: 2.8 CFM at 90 PSI with 150 max, large 6-gallon reserve tank, impact-resistant shroud to protect-Gauges, weighs only 38-Pound.
- SB-1850BN Brad nailer: adjustable depth guide, tool-free adjustable exhaust and no mar tip. Drives 18-Gauge brads 5/8-Inch to 2-Inch in length
- SB-150SX Finish stapler featuring bottom-load magazine, tool-free adjustable exhaust and no mar tip. Drives 18-Gauge 7/32-Inch narrow crown finish staples 1/2-Inch to 1-1/2-Inch in length
- SB-1664FN Finish nailer featuring quick release nose door, adjustable depth guide, tool-free adjustable exhaust and no mar tip. Drives 16-Gauge straight finish nails 1-1/4-Inch to 2-1/2-Inch in length
- Accessories include: 1/4-Inch by 40-Feet PVC air hose with fittings, 1000 1-1/4-Inch brads, 1000 1-Inch staples, 1000 finish nails, tool lubricant and canvas carrying case
See more technical details

 "Great Value!" 2010-04-16
By G. Fields (Central Virginia)
I had been drooling over this compressor kit at a local retailer but could not justify the $290 purchase price. Having had good experiences with other tools at a factory outlet, I was delighted to find it factory reconditioned on Amazon.



The kit arrived as promised but without tool oil. The first time I used it I found out why it was returned to the factory as it leaked air and would not build enough pressure to turn off. I completed the small project I had started and traced the problem to a leak around the threads (partially stripped) of the pressure regulator's adjusting knob. I was able to make temporary repairs and contacted the shipper. Rather than return the unit, they sent me a new pressure regulator. My repairs are still holding and I have a replacement if it fails again.



I am very pleased with my purchase and service after the sale. I would recommend the kit to any DIY'er, cabinet maker and trim carpenter.

 "Great buy" 2010-04-15
By Jeff W. Hatley (New Jersey)
I bought this kit because I was remodeling my family room. Best $$$ I ever spent. It took me less than 3 hours to do the trim and base boards in a 850 sq ft room with this baby. I'm going to replace all the trim in my house just so I can keep using this thing. Love it.

 "Cheap piece of junk designed to fail" 2010-04-13
By Toy B. Chaikin (Travelers Rest, SC)
I bought this compressor combo at Lowe's 3 weeks ago. Went home to play with it and discovered the stapler didn't work. Took it back to lowe's and they replaced it. Used it today for the first real project and the cheap plastic pressure controller stripped out and failed. The part cost me $14 and the shipping is $16! LOL!!!

 "Great Tool for the "Do-It-Yourself" Projects" 2010-04-10
By M. Minutella (Clifton, NJ USA)
Used my son's, and just had to have one. Great for putting up molding and trim. Plan on building some new planters and storage cabinets. Easy to use. Ample hose length and the guns are easy to handle. Unit is lightweight for easy moving, but will handle heavy jobs. I picked up the Air gun attachment, which comes in handy for cleaning the saw dust out of my power saws. Good quality at a great price.

 "Bostitch" 2010-02-01
By D. Sperle
I purchased this on-line rather because it included the combo kit that I could not find in stores. It has been great. I changed out 7 windows and used this to help replace all of them. The compressor and nailer worked great just like I knew they would. Had an oil spill during from the bad oil bottle included but all else is great.


Images Product

Buy Bostitch CPACK300 3-Tool and Compressor Combo Kit Now

read more “Bostitch CPACK300 3-Tool and Compressor Combo Kit”